Full Face Mask Recommendation?

[Dan8585]

I've been using the large size Airtouch F20 mask even though it is a bit too big, pressing into my forehead and requiring me to keep the straps tight to prevent leaks from my cheek area (though the foam cushion helps with that).  The medium size mask was more comfortable and less leak prone but it held my mouth shut, defeating the purpose of a full face mask (which I need due to nasal congestion). 

Now that my DME provider says it's time for me to replace my headgear (which is in fine condition), I thought perhaps I should try a different full face mask/headgear.  Any recommendation for one with a mask size that may fall between the Resmed F20 medium and F20 large cushion sizes?

Thanks!

P.S.  My first mask and headgear was the Philips Respironics DreamWare Full Face Mask which snuggled under my nose.  I found it to be very noisy and uncomfortable.  So I'd like to stick to a traditional full face mask.

[Dan8585]

After some quick research, the F&P Vitera looks promising.  I like that the cushion section does not extend above the bridge of the nose like the F20, and that there is a headgear adjustment on top of the head (the Resmed F20 mask tends to sit too high on my face and there is no vertical adjustment).  Any idea whether I should try the Medium or the Large size Vitera mask?  [The medium F20 was a little too small for me and the large is a little too big....but that might not be an issue if there were a vertical height adjustment.]

[gainerfull]

After some quick research, the F&P Vitera looks promising.  I like that the cushion section does not extend above the bridge of the nose like the F20, and that there is a headgear adjustment on top of the head (the Resmed F20 mask tends to sit too high on my face and there is no vertical adjustment).  Any idea whether I should try the Medium or the Large size Vitera mask?  [The medium F20 was a little too small for me and the large is a little too big....but that might not be an issue if there were a vertical height adjustment.]

One thing to keep in mind with the Vitera is it inflates the cushion to seal and I had a hard time getting my leak rate below 5L. It's worth a try though just make sure whomever you buy it from will let you swap it out if it doesn't work. Also, the regular F20 nasal pillow fits me better than the one with the foam around it if you're looking for another option.

[Dan8585]

One thing to keep in mind with the Vitera is it inflates the cushion to seal and I had a hard time getting my leak rate below 5L. It's worth a try though just make sure whomever you buy it from will let you swap it out if it doesn't work. Also, the regular F20 nasal pillow fits me better than the one with the foam around it if you're looking for another option.

I'm not worried about swapping out the headgear, though i may end up needing to buy a different size replacement cushion.  BTW, I did not think the F20 or the Vitera had "nasal pillows."  I think the Resmed 30i and the Dreamware mask (which i hated) use nasal pillows; a sleep tech subsequently advised me to avoid that style of mask.

[NightyTighty]

I'm using the Vitera right now - had it for over a year.  Advice: just order yours with the "Fit Pack" and you'll get all three sizes of cushions.  Same price as single cushion order.
    The only issue I have with it is you can't adjust the pressure on the top of the mask so it seals around the nose more tightly.
Also, the large could stand to be a bit larger for me to get around my Italian nose...
    It's been a good mask but my next one will be the Simplus just to see if I can further improve the fit.
Last mask was a ResMed Quattro.  It worked fine but the headgear straps were always wearing out.  Finally had enough of that bother and got the Vitera.  Much better material and workmanship - F & P is a good company, IMO...