+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: can you please review my data ? (/Thread-can-you-please-review-my-data)
Pages:
1
2
can you please review my data ? - kappak - 03-13-2023
I am using airsmed 10 since the last 12 months
I was diagnosed AHI 17
I use nasal pillow and tape on my mouth
based to this data AHI is low
but still don't feel very rested
some days I wake up tired and with headache
Can you please check my chart and see if I am doing something wrong ?
Thank you
RE: can you please review my data ? - kappak - 03-13-2023
looking now at some charts in this forum
why my flow rate has big empty spaces
I keep my mask on all night
this is the data of my apnea test of January 2022
Apnea/Hypopnea Index (AHI) = 17.2/hr.
Minimum O2 saturation was 90%;
Respiratory Disturbance Index (RDI) = 22.4/hr.
RE: can you please review my data ? - cmpman1974 - 03-13-2023
Those are some of the lowest pressures I've ever seen. I didn't even know someone could go down to that. That's one way to get the low leak rate!
The AHI numbers look excellent, but not a big amount of sleep per night.
RE: can you please review my data ? - kappak - 03-13-2023
(03-13-2023, 11:09 PM)cmpman1974 Wrote: Those are some of the lowest pressures I've ever seen. I didn't even know someone could go down to that.
Maybe I am doing something wrong because believe I don't feel rested
I always slept 6/7 hours per night even before sleep apnea
RE: can you please review my data ? - cmpman1974 - 03-13-2023
(03-13-2023, 11:12 PM)kappak Wrote: Maybe I am doing something wrong because believe I don't feel rested
I always slept 6/7 hours per night even before sleep apnea
I'm right there with you. My AHI numbers have consistency been between 0.1 - 0.5 this week and I'm yawning a hundred times a day. Most nights I get 8+ hrs of sleep, but again zero change in how I feel. Makes no sense. in my case, I suspect it may be low O2 stats at night still. Have you verified continuous O2 during sleep for a baseline? I'm sure others will have better insight on possible reasons.
RE: can you please review my data ? - fishfinderG - 03-14-2023
Are you saying that you aren’t taking off your mask at night at all? It sure looks like you take it off several times. You might need to turn off the auto-off feature. Your machine might be turning off for long stretches of the night by itself because it incorrectly thinks you took it off.
RE: can you please review my data ? - kappak - 03-14-2023
(03-14-2023, 07:27 AM)fishfinderG Wrote: Are you saying that you aren’t taking off your mask at night at all? It sure looks like you take it off several times. You might need to turn off the auto-off feature. Your machine might be turning off for long stretches of the night by itself because it incorrectly thinks you took it off.
Correct
I don't take it off
How do you turn off that feature in the airsense 10
Thank you
RE: can you please review my data ? - Sleeprider - 03-14-2023
You are using a pressure of only 4.6 to 20 with EPR 3, and your pressure rarely moves higher than 6.0 cm. As a result of the EPR your expiratory pressure never rises above 4.0. I'm going to suggest some setting changes that should improve your therapy and prevent the machine from shutting down, however you will have to manually turn your machine on and off.
Mode: Autoset soft
Minimum pressure: 6.0
Maximum pressure 8.0
Ramp: Off is preferred, or use Auto
Ramp Pressure: As needed, minimum is 4
EPR On
EPR Type: Full-time
EPR Setting: 2
Essentials: Plus
SmartStart: Off or disabled
SmartStart is a feature that detects patient breathing and automatically starts and stops the machine. It should not be used with nasal pillows at pressure less than 7.0 which is why it is malfunctioning for you. The Essentials settings are either on or Plus. We use plus to give you extra setting options in the patient menu including Smartstart. This recommendation to raise minimum pressure to 6.0 allows you to use EPR of 2 and the exhale pressure will still be 4.0, which is the minimum pressure of the machine. By ensuring that the minimum pressure is at least 4 with EPR, the machine will be able to properly respond to any events and EPR will remain constant. These settings will stabilize your pressure and will prevent the machine from turning off automatically.
RE: can you please review my data ? - kappak - 03-14-2023
I set up smartstart and ramp time as Off
and now I found how to change the other settings
excited to test them tonight :-)
thank you !
RE: can you please review my data ? - Sleeprider - 03-14-2023
All settings are accessible by using this procedure: https://www.apneaboard.com/resmed-airsense-10-aircurve-10-setup-info
I want to encourage you to get the clinical manual for your machine by requesting it through the forum. You can obtain a copy of the setup manual by following these instructions: Please send an email to: apneaboard@gmail.com and put "Setup Manual" (without the quotes) in the subject line. Then, let us know in the body of your email include: ResMed AirSense 10 AutoSet