+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Backup power options for CPAP machines (/Thread-Backup-power-options-for-CPAP-machines)
RE: Backup power options for CPAP machines - Barty1515 - 10-08-2018
:thanks: So how did it go. What are you using now. Interested to hear all about you're experience
RE: Backup power options for CPAP machines - terp1984 - 10-09-2018
After using my Medistrom dual battery configuration for over a year, I thought I would provide an update on my experience. I have yet to have a power outage and therefore have not had to rely on the batteries as backup power. However, I did perform a test to determine if these would work under maximum current draw. I connected my ResMed S9 VPAP Adapt as I normally would but without the mask attached. I then unplugged the S9 power supply from the wall. The CPAP continued to run as if nothing happened. About an hour later, the secondary battery was completely drained. About an hour after that, the primary battery was completely drained and the alarm sounded.
Again, I would like to point out that this is a worst-case scenario. I highly doubt anyone would be continuously using maximum CPAP pressure. Since the VPAP Adapt is designed to adjust pressure as needed, my earlier post speculating about five hours of backup usage for my situation seems reasonable.
Also, it is worth pointing out that Medistrom has discontinued its Pilot-24 Plus battery (and Co-Pilot). It now sells what it calls Pilot-24 Lite (also indicated in other threads). It is lighter than its predecessor, has slightly less power and does not yet have a Co-Pilot equivalent. In other words, you can use one and only one battery at a time.
As of this writing, there were still new Pilot-24 Plus batteries for sale on eBay.
RE: Backup power options for CPAP machines - mckevin32 - 10-14-2018
Well, since we're updating,
I built my rig (from page 3) around a year ago as well.
A PWRGATE PG40S mounted on a Minn Kota Trolling Motor power center (batt box with 2 12v cig lighter outputs). Power supply to the PS input, deep cycle battery to the BATT, and the output to the cig lighter plugs on top of the box, where the Dreamstations plug in with OEM 12v cords.
We have 2 Dreamstations running on it nightly. There have been a few brief outages and, happily, there is zero noticeable lag in switchover, so we don't wake up.
More importantly, we had a significant outage a month or so ago. Power was out for 2 full nights. This rig powered both units for both nights, humidifiers and all, with no complaints.
My wife thinks I'm a danged genius, lol...
RE: Backup power options for CPAP machines - purpleh2 - 10-18-2018
[attachment=8827][attachment=8828]
Resmed Airsence 10 Elite, slim line tubing, pressure 16, Humidifier at 4
Just thought on a cheaper Battery back-up for home or camping use
Looking at the spec. sheet of Resmed electrical draw (16 pressure, 40AH, 3.33 amps )
This battery should be go for 90 hrs is this correct
Thank You
Mike
RE: Backup power options for CPAP machines - LeeKopp - 10-18-2018
In my situation, living in the Sierra mtns @ 4K ft, I'm in need of a backup solution other than the generator - which I have but would normally turn off before going to sleep. (a generator running solely for a CPAP seems overkill.) Our power outages can be days long, but mostly are ~ 2 or 3 days. (Almost 3 wks down in the El Nino year 1997.) I could recharge the battery backup for the APAP - using the generator during the day. I have a DreamStatiom APAP.
RE: Backup power options for CPAP machines - purpleh2 - 10-18-2018
I am wondering if my calculations are right, does anyone have a electrical back ground
you have the 2 attachments and the thumbnail
and what draw the AirSense 10 has
Thanks
Mike
RE: Backup power options for CPAP machines - jaswilliams - 10-18-2018
(10-18-2018, 03:16 PM)purpleh2 Wrote: I am wondering if my calculations are right, does anyone have a electrical back ground
you have the 2 attachments and the thumbnail
and what draw the AirSense 10 has
Thanks
Mike
There is no way that booster pack has a capacity of 300 ah it just has the ability to provide upto 300 Amps for a short period of time. I would be very surprised if the battery in there is rated at 10 to 12 amp hrs, but with the specifications you posted it does just not provide sufficient information
If you look at the size and weight of a large leisure battery that has the capacity of 120 amp hrs you can see how your calculations are flawed sorry as to have 300ah it would need to be 3x the size and weight
RE: Backup power options for CPAP machines - purpleh2 - 10-18-2018
[attachment=8839]
Thank You Jaswilliams
I looked at it more closely and the table supplied, and its J312B --- 7 aH, so if lucky maybe last 2 hrs.
So looking at the picture, model Number JUS500B is rated 19 AH and my air sense 10 is 3.3 aH
so it should just a little over 5.7 hours if prefect conditions, if not maybe 4.5- 5 hrs
Thanks again for you reply
RE: Backup power options for CPAP machines - terp1984 - 05-03-2024
I recently purchased Zopec Explore Oxygen CPAP Battery from Amazon for $800. It is not an ideal solution, but it is definitely the best solution I have used so far. After fully charging it, I did a test using it as stand-alone power. Despite the vendor's recommendation, I used my normal settings for humidity and heated hose (much higher than suggested). In the morning, it had 56% power left - good enough for me. Since then (about eight months), I have been using it as an UPS. Again, my settings are way higher than suggested and only one time did the battery lose any of its power. In other words, in all but that one case, the pass-through power was sufficient to prevent the battery from losing any juice.
What I like:
It will definitely work as a true UPS.
It will provide more than one night's sleep for me.
What I don't like:
It is inefficient. In other words, A/C power to battery to A/C plug to CPAP power supply. I liked the design that had CPAP power supply to battery to CPAP machine. Unfortunately, that setup (of those I have seen) will not provide even one night's sleep if power is lost.