+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: AIRFIT F10 LEAKS (/Thread-AIRFIT-F10-LEAKS)
Pages:
1
2
AIRFIT F10 LEAKS - dizzy1 - 06-04-2017
I have been using my new AIRFIT F10 mask the past 4 nights. The results show the mask is leaking way to much.
I can feel no leaks around the rubber seal on my face at all but when I cover the exhaust holes I can feel air leaking from where the pipe fitting clips into the mask.
I think this mask is of poor design or has been made faulty. Other than that I find the mask headgear and mask fit very good indeed.
I was thinking if taping the fitting that goes into the mask but that would stop the hose from turning when I move in my sleep.
I feel much more tired and fatigued the past few days and I am sure it is because of the mask leaks and not getting proper cpap therapy because of this.
Anyone have any ideas or experience with this mask?
RE: AIRFIT F10 LEAKS - ajack - 06-04-2017
the side holes are for the flap released air/ low pressure or off, it opens so you don't suffocate.
the air leaking around where the pipe goes in is the bleed air, that is also so you don't rebreathe air.
inside the hole I think there should be a rubber seal, as least there is on it's sister mask the Quattro Air which has the same cussion.
so everything points to the mask being fine. how much is sleepyhead saying it's leaking and have you got the setting to full face in your machine, if there is one for masks?
RE: AIRFIT F10 LEAKS - dizzy1 - 06-04-2017
Many thanks for your help. After looking more closely at the mask I can see the mask leaks I mentioned are there for a reason.
I am thinking that maybe I need to lower the pressure a little and see how it goes tonight.
With my previous mask the QUATTRO FX I could not go above 11 pressure as I would get blow outs at 11.5 and higher.
Maybe if I turn pressure down to 10 and see how it goes.
I dont have the airfit f10 too tight nor too loose and turning over and changing position during testing caused no leaks.
Leak results from last night below:
Average Leak Rate 21.87
90% Leak Rate 31.00
% of time above Leak Rate threshold 50.08%
RE: AIRFIT F10 LEAKS - dizzy1 - 06-04-2017
No setting on machine to choose mask type
RE: AIRFIT F10 LEAKS - silversnore - 06-04-2017
Can you post your sleepyhead reports, some PR machines have two reportings of leak data, one for the intentional designed leak for CO2 safety reasons and the other unintentional leaks, failures of mask seal, etc. Does your report indicate two lines on your leak graph?
Does your machine have a System One Resistance Setting?
RE: AIRFIT F10 LEAKS - dizzy1 - 06-04-2017
There are 2 lines on the leak graph but I do not know what they are?
There is a c-flex+ setting from 1 to 3 and it is set to 3.
Sleepyhead results from last night below:
http://imgur.com/a/86EEa
RE: AIRFIT F10 LEAKS - Gideon - 06-04-2017
(06-04-2017, 07:57 AM)dizzy1 Wrote: Many thanks for your help. After looking more closely at the mask I can see the mask leaks I mentioned are there for a reason.
I am thinking that maybe I need to lower the pressure a little and see how it goes tonight.
With my previous mask the QUATTRO FX I could not go above 11 pressure as I would get blow outs at 11.5 and higher.
Maybe if I turn pressure down to 10 and see how it goes.
I dont have the airfit f10 too tight nor too loose and turning over and changing position during testing caused no leaks.
Leak results from last night below:
Average Leak Rate 21.87
90% Leak Rate 31.00
% of time above Leak Rate threshold 50.08%
Your leak numbers look fine, your % of time above Leak Rate Threshold I think is you took the default which is a ResMed number. PR is Much higher (varies by a number of factors but 60 is likely a good value. Can you post your charts so we can see for sure. See my sig for how to.
RE: AIRFIT F10 LEAKS - Gideon - 06-04-2017
When Sleepyhead detects a large leak you get a grey bar covering the time that was so. You have none, you have no "large Leaks "LL"
RE: AIRFIT F10 LEAKS - silversnore - 06-04-2017
Ok, the top line on your graph is the intended leak for your mask, this leak keeps you from rebreathing CO2, it also contains you leaks that are not intentional. The lower line is your leak rate that you want to control. There is a certain point that your machine cannot pump enough air to keep up with the links, I am not sure about PR machines, but anything over 24l/m on resmed's is the limit. There should be a Resistance setting in your menu, I think that this is similar to other machines and how you select masks. As you are using a resmed mask, you would have to go to the PR web site and find the settings for a similar size ffm.
You are having a good deal of snoring and you could have better control of your apneas. I am not quite sure how flex works it may be similar EPR on resmed's machines. You should start another thread asking for evaluation of your sleepyhead report. You probably need to reduce your flex or up your pressure, however you should get an opinions from other sr. members.
RE: AIRFIT F10 LEAKS - Gideon - 06-04-2017
- Philips-Respironics System One: There is no official "line in the sand" for flagging a Large Leak.
- Series 60 System One users may start to see Large Leaks being flagged when the Total Leak Rate reaches 60-70 L/min; if the prescribed pressure setting is below about 8cm, then Large Leaks may be flagged when the Total Leak Rate reaches 50-60 L/min in some circumstances.
- Series 50 System One users may start to see Large Leaks being flagged when the Total Leak Rate reaches 80-90 L/min; if the prescribed pressure setting is below about 8cm, then Large Leaks may be flagged when the Total Leak Rate reaches 60 L/min in some circumstances.