Apnea Board Forum - CPAP | Sleep Apnea
Resmed AirCurve10 VAuto Bi-pap SD Problems? - Printable Version

+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Resmed AirCurve10 VAuto Bi-pap SD Problems? (/Thread-Resmed-AirCurve10-VAuto-Bi-pap-SD-Problems)

Resmed AirCurve10 VAuto Bi-pap SD Problems? - Grammy25 - 09-22-2020

Hello. I’m new here and I just transitioned from a Resmed S-9 VAuto in Bi-Pap mode to a Resmed AirCurve10 VAuto in Bi-pap mode. I have the Resmed software but am considering getting Oscar. What I would like to know BEFORE removing my card and putting it in a card reader is will the Aircurve10 have the same problem reading a card that Windows10 writes volume information on like my S-9 had? I find that it was really a pain to have to run CMD prompt and remove volume info every single time I read the card. I also don’t want to loose any info on my card before I see my Dr again. I know I can read all the info from the machine and do glance at it everyday because I’m trying to battle out mask leaks but would like to see all the info I can from the last week or so without risking loosing any of the information on my card. Thanks in advance  Rolleyes

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Crimson Nape - 09-22-2020

The A10 series doesn't have the problem that the S9 does with System Volume Info. You should be good to go.

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Grammy25 - 09-22-2020

Thanks for the quick reply! So good to know! That volume info was a real pain with the S-9.

Thanks

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Crimson Nape - 09-22-2020

You could have engaged the "Write Protect" option on the card or disable the system volume writing feature in the O/S.  For your knowledge, OSCAR does not write anything to the card.  Unless you use the parameter change feature in ResScan, it doesn't write anything either.

Here are the steps on Windows 10 to disable it:
  1. Right click "Computer"
  2. Select "Manage"
  3. Double click "Services and Applications"
  4. Single click "Services".
  5. In the right pane, scroll down and find "Storage Service".
  6. Right click, and select "Properties".  
  7. If it is running, click the "Stop" button.  Then in the dropdown labelled "Startup Type:" select "Disabled"
This will prevent the unnecessary storage service from running, since it is responsible for creating System Volume Information on SD cards and USB drives.

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Grammy25 - 09-22-2020

I always “lock” the card but somehow windows gets around the lock? I also tried disabling the storage service but volume info was still being written to the card somehow? I did a re-boot after disabling it but it still wrote volume info to my card-I did go back and see if that service was running and it showed it was disabled. Not sure why card was being written to? I just ran the CMD prompt and removed it every time I used it in computer to make S-9 happy.

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Crimson Nape - 09-22-2020

OK you might try this: Disable/EnableSysVolInfo

RE: Resmed AirCurve10 VAuto Bi-pap SD Problems? - Grammy25 - 09-22-2020

Thanks! I’ll try that. Hopefully it will turn it off and nothing Will be written to card.

Thanks Sleep-well