+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: [Equipment] My First Night. One question & your thoughts (/Thread-Equipment-My-First-Night-One-question-your-thoughts--9794)
My First Night. One question & your thoughts - JerryLeeK9 - 06-04-2015
[attachment=1531]
Hello all. First thank you all for this board and the information you have provided.
With your help and some research I upgraded my machine to PRS1 Auto Flex (550)(I previously had used the Remstar Plus M Series C Flex). I was able to find a used one with about 500 hours on it for $150. My original setting (7yrs ago) was 8 cm/H20. I am about 25 lbs heavier now. BMI is 32
So... last night was my first shot at this. After cleaning the machine, I set the machine as shown above. I chose 6 min and 14 max, as an estimate base on information I had read, as well as my original number years back. It looks like it was a pretty good night (your comments would be appreciated).
It did take a while for me to fall asleep. That is unusual for me, as I generally am out 5 min after I hit the pillow. I am assuming just the (re)newness of having the headgear/pillows had a bit to do with it. I did wake up for a few hours during the night. I think it was around 1:30 or 2am until around 3:30 or 4am. (I am sure there is a way to tell, based on the graphs). Waking up during the night has not been that uncommon for me, especially if I go to sleep early. While I was awake, I did adjust the nose pillows once (pulled them away from my nose).
This morning I did feel a little foggy, and actually still do, after a few hours of being awake.
So.. my 2 questions:
1) Do you see any reason why I could not raise the min number to 7 or 7.5?
2) On the data card, which file / files would I erase, to rid the card of the previous owners data. I dnk if the answer is all of them, and then the machine will rewrite what it needs, or if there is a specific data file.
Thanks for taking the time to read this. Please give your opinions, questions or concerns. This is obviously my first shot at SleepyHead, and your guidance would be greatly appreciated.
RE: My First Night. One question & your thoughts - Sleeprider - 06-04-2015
To be sure you eliminate all of the existing patient files, simply format the SD card to FAT 32. The machine will recognize it as a new card. Before putting it in the machine, you need to erase all existing therapy data. Turn dial to setup and push both the control dial and ramp button until you hear two beeps. Now dial INFO and look for the reset data option.
Once the data is reset you can exit and insert the SD card. Now if you want to change the settings, go back into clinical menu, setup and change the pressures. This will write new data to the card.
It's fine to increase your minimum pressure. Once you collect a few nights of data, we can take a look at what your results are, and if adjustments are needed, I generally like to set the minimum pressure between the median and 90% pressure, and add 5 or more for maximum pressure. The machine will only go up as much as necessary, but will "trial" +2.0 cm above whatever pressure it is at about every 10 minutes. Eventually you may choose to narrow the range.
RE: My First Night. One question & your thoughts - Sleeprider - 06-04-2015
Just a quick add, to reset the therapy hours when you reset the data. You will also see machine hours in this menu if you want to verify the actual hours of use the machine has had as opposed to resettable therapy hours.