Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

CMI PL-66 OE data import format
#1
CMI PL-66 OE data import format
Here's a .cvs file (first few lines) produced by the CMI provided program Oximeter Data Manager. 5.5.0.0

Code:
# No.: 1, Name: Jared, Start: 5/2/2021 12:58:47 AM, End: 5/2/2021 1:02:33 AM, Interval : 1sec, Mode :(1)Adult
# Time, SpO2(%), PR(bpm)

05/02/2021 00:58:47  , 98 , 82
05/02/2021 00:58:48  , 97 , 80
05/02/2021 00:58:49  , 97 , 78
It should be trivial to turn this into something that the Oscar OE Wizard can accept.

If one of the Oscar programmers would step up the a file format, I'll gladly write a conversion program to output it into Oscar readable format.

This should pay off for almost every CMI device as they all seem to use same program to upload from the device/manage patients etc.
Post Reply Post Reply
#2
RE: CMI PL-66 OE data import format
The CSV file layout looks very similar to some raw data files I've seen. Do you have the raw data file that produced the listing above?
Crimson Nape
Apnea Board Moderator
Project Manager for OSCAR - Open Source CPAP Analysis Reporter
www.ApneaBoard.com
___________________________________
Useful Links -or- When All Else Fails:
The Guide to Understanding OSCAR
OSCAR Chart Organization
Attaching Images and Files on Apnea Board
Apnea Helpful Tips

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
RE: CMI PL-66 OE data import format
Short Answer:
  That IS the raw data.

Long Answer:

* You want to go after the machine?  It has a virtual com interface that can be traced.

* You want to go against the program?  It has a very large and sparse data base that has all patients, all data, etc.  No obvious structure like MySQL, etc.

  There are some temporary files which might be captured with the program open, patient selected, record selected, fingers crossed.

* What's wrong with taking the easy way and not hacking so much? 

Back to the original question:

  I can point Oscar OX wizard at an MD300W1.dat file. 

  What does it look like, and what has to be present?

Sample Answer:

- GO to GITHUB or what ever Oscar uses,
- PULL project oscarox or what ever contains the import code,
- LOCATE the file(s) asdf and ghjk,
- LOOK at structures abc, xyz, and tuv for the data layout.
  Line 5678 of ghjk starts the read/parse of MD300W1.dat
Post Reply Post Reply
#4
RE: CMI PL-66 OE data import format
OK, I've cracked the data base and record format.

Will a OSCAR developer PLEASE get in touch with me to talk about adding support?
Post Reply Post Reply
#5
RE: CMI PL-66 OE data import format
(05-15-2021, 11:48 PM)HiTechHiTouch Wrote: OK, I've cracked the data base and record format.

Will a OSCAR developer PLEASE get in touch with me to talk about adding support?

Hi,


I am trying to do something similar, but I cannot find a sample .spo2, spr, or .dat file online. 

Did you manage to resolve this? Any help or tips that you can provide?

Thank you!
Post Reply Post Reply
#6
RE: CMI PL-66 OE data import format
(05-15-2021, 11:48 PM)HiTechHiTouch Wrote: OK, I've cracked the data base and record format.

Will a OSCAR developer PLEASE get in touch with me to talk about adding support?

Hi,  I am also trying import data in a similar session file (data is from an EMAY device, which readily exports in CSV format.)
The CSV data is available to me on the same Win10 machine as OSCAR is installed on; no need to hook a cable to the SpO2 device, no need for a specific device driver, etc. 
If some special header for patient data is needed at the beginning of a file, that should be quite easy to add to the CSV file, but in my case there is only one patient.

Did you have any luck in this project?  I can see that several other users are having the same problem over that past several years.  
It would be extremely helpful to have a method to import this CSV data into OSCAR to view along with the APAP data.  Thanks in advance!

Example data from actual file:

Date,Time,SpO2(%),PR(bpm)
10/28/2023,12:08:29 AM,88,88
10/28/2023,12:08:30 AM,88,88
10/28/2023,12:08:31 AM,88,88
10/28/2023,12:08:32 AM,88,87
10/28/2023,12:08:33 AM,88,87
10/28/2023,12:08:34 AM,88,86
10/28/2023,12:08:35 AM,88,86
10/28/2023,12:08:36 AM,88,85
10/28/2023,12:08:37 AM,89,85
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Question Spo2 data format Squid3083 12 3,342 Yesterday, 06:14 AM
Last Post: aradhana
  O2 import DST > ST 1:14am happened twice dgconder 5 261 11-03-2024, 08:55 PM
Last Post: dgconder
  Oscar Crash to desktop on SP02 import WallyPepper 7 693 11-01-2024, 09:36 PM
Last Post: Crimson Nape
  Trouble understanding how to import O2 ring info into Oscar katbrat 6 514 10-26-2024, 08:25 PM
Last Post: katbrat
  OSCAR: Questions regarding a potential import for Garmin data littleyoda 2 279 10-19-2024, 10:37 AM
Last Post: littleyoda
Idea Generic import to OSCAR? Oscer? I Ardly Know Er 1 426 10-19-2024, 03:48 AM
Last Post: littleyoda
  EncorePro 2.24 - change date format fredong77 1 201 10-13-2024, 08:53 AM
Last Post: Crimson Nape


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.