Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

ResMed S10 Auto set Measured vs Actual Pressure
#1
ResMed S10 Auto set Measured vs Actual Pressure
Hi I picked up ResMed S10 Autoset today.  While at clinic the technician attached a pressure measurement device which showed pressure of 8.7 measurement.  Only problem is that the machine was set to 8.0. What should I do in this situation?
Post Reply Post Reply
#2
RE: ResMed S10 Auto set Measured vs Actual Pressure
Welcome to the forum.
Did you ask him why the reading did not match the setting? I'm assuming you accepted the machine even though the pressure reading did not match the setting. You may need to return it for service or replacement.
Download OSCAR

Organize Charts
Attaching Charts

Mask Primer
Soft Cervical Collar

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.

Post Reply Post Reply
#3
RE: ResMed S10 Auto set Measured vs Actual Pressure
Yes I accepted the machine.  Difference of 0.7 did not bother me. Is it a reason for concern? If it is, I will go back and tell him to fix it or service it.
Post Reply Post Reply
#4
RE: ResMed S10 Auto set Measured vs Actual Pressure
That is too much error and you should insist that your machine gives accurate measurements. These are medical devices and they are supposed to meet standards.
Ed Seedhouse
VA7SDH

Part cow since February 2018.

Trust your mind less and your brain more.


Post Reply Post Reply
#5
RE: ResMed S10 Auto set Measured vs Actual Pressure
The specs are probably in range, if not a tad on the high side
Mask pressure ±[0.5 cm H2O + 4% of measured value]
https://www.respshop.com/manuals/ResMed-...%20her.pdf

It won't really matter, as you will adjust your numbers on your AHI results, Get the manual and sleepyhead program from the top of the page
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
For auto-cpap, from machine data or software. You can set the min pressure 1 or 2cm below 95%. Or clinicians commonly use the maximum or 95% pressure for fixed pressure CPAP, this can also be used for min pressure.
https://aasm.org/resources/practiceparam...rating.pdf
Post Reply Post Reply
#6
RE: ResMed S10 Auto set Measured vs Actual Pressure
(06-26-2017, 05:27 PM)ajack Wrote: The specs are probably in range, if not a tad on the high side
Mask pressure ±[0.5 cm H2O + 4% of measured value]
https://www.respshop.com/manuals/ResMed-...%20her.pdf

It won't really matter, as you will adjust your numbers on your AHI results, Get the manual and sleepyhead program from the top of the page

+1.
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Low vs high pressure Resmed sleep4 2 122 11-22-2024, 01:20 PM
Last Post: staceyburke
  Airsense 11 Auto - What is auto-off supposed to do? Schnoozer 3 251 10-31-2024, 07:33 PM
Last Post: Warnick13
Rainbow Sleep-Wake-Junk or Actual OSA? pvjoc 0 380 10-17-2024, 06:41 PM
Last Post: pvjoc
  pattern in high resolution mask pressure in resmed device rberry1 1 301 09-11-2024, 07:51 PM
Last Post: Deborah K.
  Is it normal for Resmed 10 blowing noise to be very noticable at high pressure >13 snortle 4 392 08-29-2024, 09:49 PM
Last Post: SarcasticDave94
Question Z2 pressure vs Airsense11 pressure jwalker5 2 287 08-17-2024, 12:11 PM
Last Post: jwalker5
  [Pressure] Resmed Aircurve 10s - pressure and leaks ManGoLine 0 244 08-12-2024, 01:08 PM
Last Post: ManGoLine


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.