Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Sharing my observations on refreshing old f30i masks
#1
Sharing my observations on refreshing old f30i masks
Hi All,

I used to do hazmat. We also use silicone masks. While we replace masks every year or so, we don't really have to. They last more or less indefinitely so long as they're taken care of. So why do CPAP masks fail? Because they're designed to from what I can tell. So I got annoyed. Thought I'd share my results to save others the effort of repeating experiments. Not positive this goes here so please move it if it doesn't. 

Someone on here stated that masks could no longer be boiled because many of them now contain plastic. This is not necessarily true. I use f30i masks, which have a large plastic section. Not all plastics melt at 212F/100C. I tried boiling an old f30i. First in a baking soda only solution for about an hour, which didn't melt but also didn't make it seal again and then in a water/baking soda/dish soap solution for around 3 hours (I actually forgot about it but let's pretend I meant to do that.) Which didn't melt it but also didn't make the mask go back to sealing correctly. 

Figured it couldn't hurt to try pressure cooking the mask since it already didn't work. Worst case I had some melted plastic in a steel pot that I might have to power tool out. Put it in a baking soda only solution in the instant pot for 10 minutes on manual with manual release @ 20 minutes with the pot a bit under 1/2 full. I don't know how long it will last as I only tried that yesterday, but it seals like new again. And, obviously, didn't melt. There's no visible change to it after being put in the pressure cooker. Will endeavor to post updates, including negative results. 

Another thing I tried, since I mostly get leaks around the nasal area, was to reinforce that area with 00-20 silicone (super soft silicone, similar to that used in the mask, think squeezing a gummy bear.) That did work, however my nose was a bit sore in the morning, nothing too terrible but less than perfect, as the reinforcement made the mask slightly less flexible. I used 5ml (3ml wasn't enough) of 00-20 silicone and held the mask in place (upside down and tilted a bit forward) by cutting slots in the sides of a medium sized yogurt cup. While there are glues that will help silicone to stick to silicone I didn't use any, just cleaned the mask with soap, rinsed it with water, dried it and applied liquid silicone. If I was doing it again I'd pressure cook it in baking soda and just rinse it off with water as I think the soap may have formed a film that interfered with the bond between old and new silicone. In my case that was actually a good thing as it makes it possible to pull the new silicone out and try again or just pressure cook the mask instead. Would probably last about a week if I kept using it before the new silicone falls out. If pressure cooking doesn't continue to work I'll revisit this, maybe try to find some silicone even softer than 00-20 or just try to apply the silicone to the inner part of the nasal channel rather than filling the whole thing so it's a bit more flexible. 

My next idea, depending on how long a pressure cooked mask lasts, is to use an oven at various temperatures. Since I'm concerned about that melting the plastic the thought was to take a deepish loaf pan, fill it with water, and position the mask such that only the silicone nasal portion is above the water line. Then bake at temperatures starting around 250F to see if I can get the same shrinking effect people get with their silicone phone cases but just on the nasal area that's leaking. So long as the plastic part of the mask is below water it will never exceed the boiling point of water, but the nasal portion that's above water should be closer to the temperature of the oven. Positioning would be a challenge and I planned to hold the mask in place with 3d printed supports using magnets adhered to the bread pan, though a similar effect could probably be attained by running thin metal wire (solid stripped ethernet wire or just fishing line if it can stand being boiled) through the exhaust holes in the mask and attaching that to weights if you want to try this and don't have a 3d printer. The same idea could be done with a heat gun (or a torch if you're more confident than I am) in case the boiling water in the oven lowers oven temps too much. That would take a bit more finesse and might produce less reliable results. Still, if the mask is trash anyway may be worth a go. Again, haven't tried this, it was just the next idea. 

Another thought is to use the glue (I think spirit gum) used in costuming around problem areas before bed. Which is likely a lot cheaper than buying a new mask each month, given how little of that glue would be required for just the nose or just contact area around the cheeks/chin or wherever your mask leaks when it fails. Haven't tried that and no idea how hard it is on the skin. Would make removing the mask at night a real pain. Personally I drink through a ptfe tube I shove up under the bottom of the mask so as not to take it off, but if you do remove yours it'd be a pain.

Anyone have anything that works better for them than the ideas I've listed here?
Post Reply Post Reply
#2
RE: Sharing my observations on refreshing old f30i masks
I'm new to this. For the various methods you tried, what problem were you trying to solve?
Post Reply Post Reply
#3
RE: Sharing my observations on refreshing old f30i masks
I use cleaning wipes on my masks. Simple & easy to do. I just don't see myself needing to use heat to clean a mask.  Dont-know
Post Reply Post Reply
#4
RE: Sharing my observations on refreshing old f30i masks
Seems like a lot of trouble to avoid "buying" 1 mask /year no?
Post Reply Post Reply
#5
RE: Sharing my observations on refreshing old f30i masks
I'm poor and can't complete a sleep test. Masks fail and leak after a while and have to be replaced. Since I can't complete a sleep test I have to pay for them. So I'm either going to figure out how to stop the mask from failing or I'm going to make a mask that doesn't fail. The former seems easier so that's where I started. 

Other people may not have insurance that covers these masks so do this to get more life out of them. Some people live in countries where masks are hard to get or cost a lot more than in the US and so they try to make them last longer.
Post Reply Post Reply
#6
RE: Sharing my observations on refreshing old f30i masks
No. They last me about a month before they leak too much to use. I wouldn't care if it was once a year. I care very much that it's once a month.
Post Reply Post Reply
#7
RE: Sharing my observations on refreshing old f30i masks
(07-21-2024, 03:03 PM)SkySleep Wrote: I'm new to this. For the various methods you tried, what problem were you trying to solve?

Have tried cleaning wipes. Mask fails in about a month, just like with soap. The problem I was trying to solve is that the masks starts leaking in about a month and needs to be replaced. Which I can't afford to do.
Post Reply Post Reply
#8
RE: Sharing my observations on refreshing old f30i masks
makes sense then i'd be annoyed if i had to buy a mask monthly. have you considered a home sleep test they aren't much more expensive than a mask at 200$?

here insurance is 1 /year and my n20 has lasted 3 months without issues but ffm are another beast. i just use mild hand soap once a week.
Post Reply Post Reply
#9
RE: Sharing my observations on refreshing old f30i masks
I don't go out of my way to make sure a mask lasts as long as is possible. But, I keep them clean and in good repair, and more-times-than-not, a mask will last me several months, if not longer. 

I'm fortunate and we have very good health insurance. I have a DME supplier that sends me new replacements every few months. Way more than I go thru.  Cool
Post Reply Post Reply
#10
RE: Sharing my observations on refreshing old f30i masks
Absolutely fascinating!
Anxious to hear your updates.
I just started using the F30i yesterday
Standard mask/headgear with medium cushion...
and it is a leak monster.
So much so that unless the leaks can be resolved soon, something else will have to be tried.
I said that to say this:
I have 5 new medium cushions and, if allowed by the forum, I'll give them to you.
I will try to get this darn thing adjusted first, though.
Looking forward to hear more from our 'mad scientist'!
Good luck.

- PappaJoe
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Has anyone checked to see what chemical(s) resmed masks are off gasing? erouting 18 1,266 11-16-2024, 08:21 AM
Last Post: SeePak
Question F30i makes a whistling noise Sleepy Willy 2 334 10-19-2024, 10:40 AM
Last Post: Sleepy Willy
  Does anyone know if the Dream Wear's large mask is bigger than the F30i's medium? erouting 0 189 10-04-2024, 06:28 PM
Last Post: erouting
Angry [CPAP] Resmed Mask F30i - Tabs keep breaking.. Anybody else have this problem? Snacko 6 2,747 09-24-2024, 10:37 PM
Last Post: Sis2cher
  AirFit F30i Mask Problem OldTeacher 25 7,863 08-20-2024, 12:33 PM
Last Post: ejbpesca
  Some masks better for pressures above ~8? UsuallyTired 11 715 08-18-2024, 12:51 PM
Last Post: SarcasticDave94
Angry [Equipment] Masks all either cause pressure sores or blow off my face middleofnowhere 10 637 07-10-2024, 11:55 PM
Last Post: HalfAsleep


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.