RE: Sleep Master wireless XPAP data transfer
(03-01-2016, 03:36 PM)Rick_V Wrote: Lan card192.168.0.112
255.255.255.0
Gateway 192.168.0.1
It appears that you are only seeing your computer and not the WiFi-SD card. Do you have a DHCP server or are you setting your IP's statically? If you have a 03 SD card, you could set it's IP to 192.168.0.113/24(Assuming you don't have that address assigned). Note: the "/24" is the same subnet mask as 255.255.255.0., it's just written differently.
RE: Sleep Master wireless XPAP data transfer
so I should bind it as "192.168.0.113/24" or just "192.168.0.113"?
03-02-2016, 02:41 PM
(This post was last modified: 03-02-2016, 02:42 PM by AlanE.)
RE: Sleep Master wireless XPAP data transfer
(03-01-2016, 02:36 PM)Rick_V Wrote: I have 3 wireless routers in the house one is the one from the DSL provider, the other 2 are connected to it through wired connections. Also I have a 4th access point with a Directv Genie system. Could it be trying to connect to one of the other routers and that is what is causing the problem.
Only one of your routers should be providing DHCP (or you are using all static IPs). If you have more than one DHCP on the same subnet you are going to have problems. You can check that router providing DHCP for devices connected to it. It will list, usually, by MAC address. Other option would be to use a program like netscan to scan your subnet. It will list every device it finds with the device's MAC address and what the IP is of the device.
You could get lucky and open a command prompt and type in
arp -a
You may find the MAC address on that list along with its IP.
03-02-2016, 03:55 PM
(This post was last modified: 03-02-2016, 03:56 PM by Rick_V.)
RE: Sleep Master wireless XPAP data transfer
(03-02-2016, 02:41 PM)AlanE Wrote: (03-01-2016, 02:36 PM)Rick_V Wrote: I have 3 wireless routers in the house one is the one from the DSL provider, the other 2 are connected to it through wired connections. Also I have a 4th access point with a Directv Genie system. Could it be trying to connect to one of the other routers and that is what is causing the problem.
Only one of your routers should be providing DHCP (or you are using all static IPs). If you have more than one DHCP on the same subnet you are going to have problems. You can check that router providing DHCP for devices connected to it. It will list, usually, by MAC address. Other option would be to use a program like netscan to scan your subnet. It will list every device it finds with the device's MAC address and what the IP is of the device.
You could get lucky and open a command prompt and type in
arp -a
You may find the MAC address on that list along with its IP.
OK It looks like only the router I am trying to connect to is the right one disabled one older G router and the one from the DSL provider was never active.
[attachment=2218]
I know the card is sending because when I have it in the PC I can see it on the WIFI list on my phone. Could it be some switch it the cards setup that fluxered. I had it in my AS10 when I did the scan and it don't show up.
RE: Sleep Master wireless XPAP data transfer
The range is not that good on it. How far away from your wifi router is it? Check your CONFIG file in the FlashAir located in the SD_WLAN folder. The bold lines are the most important.
APPMODE=5
APPNAME=A10FlashAir
PRODUCT=FlashAir
VENDOR=TOSHIBA
APPSSID=**
LOCK=1
DNSMODE=1
APPAUTOTIME=0
COMMAND=fat cp /SD_WLAN/BCONFIG 1:/BCONFIG
MASTERCODE=**
UPLOAD=1
APPNETWORKKEY=**********
NOISE_CANCEL=0
STA_RETRY_CT=0
03-03-2016, 08:00 AM
(This post was last modified: 03-03-2016, 08:03 AM by Rick_V.)
RE: Sleep Master wireless XPAP data transfer
(03-02-2016, 09:57 PM)AlanE Wrote: The range is not that good on it. How far away from your wifi router is it? Check your CONFIG file in the FlashAir located in the SD_WLAN folder. The bold lines are the most important.
APPMODE=5
APPNAME=A10FlashAir
PRODUCT=FlashAir
VENDOR=TOSHIBA
APPSSID=**
LOCK=1
DNSMODE=1
APPAUTOTIME=0
COMMAND=fat cp /SD_WLAN/BCONFIG 1:/BCONFIG
MASTERCODE=**
UPLOAD=1
APPNETWORKKEY=**********
NOISE_CANCEL=0
STA_RETRY_CT=0
Here is Mine
APPMODE=5
APPNAME=Rick
PRODUCT=FlashAir
VENDOR=TOSHIBA
APPSSID=Cave
LOCK=1
DNSMODE=1
APPAUTOTIME=0
COMMAND=fat cp /SD_WLAN/BCONFIG 1:/BCONFIG
MASTERCODE=*.*
UPLOAD=1
APPNETWORKKEY=*.*
NOISE_CANCEL=2
STA_RETRY_CT=0
My router "Cave" is about 10' away basically just underneath on the first floor.
RE: Sleep Master wireless XPAP data transfer
Okay, NOISE_CANCEL shouldn't matter at that distance. "Cave" is on the same subnet as your PC? and that is the one with DHCP?
RE: Sleep Master wireless XPAP data transfer
(03-03-2016, 09:28 AM)AlanE Wrote: Okay, NOISE_CANCEL shouldn't matter at that distance. "Cave" is on the same subnet as your PC? and that is the one with DHCP?
Yup, the only thing I can possibly see causing the problem (but I am not the greatest on this kinda stuff) is the Directv Genie network causing problems it has a wireless bridge to one of the tuners which is wireless.
RE: Sleep Master wireless XPAP data transfer
I'm thinking not if you specified the SSID. On "Cave", what security are you using? Flashair I believe only supports WPA2_Personal and the password has to be from 8 to 63 characters.
My encryption is set for AES (only selection available to me under WPA2).
Have you tried the Flashair software?
http://www.toshiba.co.jp/p-media/english...ware02.htm
February 15, 2016 V3.0.2
This software is good for W-02 and W-03.
The last Flashair firmware update was: August 20, 2015 V3.00.01
http://www.toshiba.co.jp/p-media/english...ol_w03.htm
Neither erased my card data despite their warning that it would, but I made a backup of it just in case. I had to manually edit the CONFIG file after as well.
03-03-2016, 02:34 PM
(This post was last modified: 03-03-2016, 02:40 PM by AlanE.)
RE: Sleep Master wireless XPAP data transfer
BTW SleepMaster is supposed to set the card up for you also. It's been a while since I used SM so I may be wrong.
Edit: But I remember it was a good piece of software to use. Jack_Russel did a nice job on it.
