+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Airsense 10 System Fault 010 has me out of commission (/Thread-Airsense-10-System-Fault-010-has-me-out-of-commission)
Pages:
1
2
Airsense 10 System Fault 010 has me out of commission - gregger - 09-29-2024
I got myself into a bit of trouble. My Airsense 10 had become noisy in the last month or so, emitting a soft moan / whistle noise from the blower/motor. I ordered a generic replacement blower/motor from Amazon and installed it carefully. When turning the machine back on, it runs for a few seconds, blowing hard, but then quits and issues System Fault Error 010. Resmed's technical service page shows this to be a stuck flow sensor, which typically is not repaired in favor of simply replacing the main PC board.
The machine is 6 years old and since I acquiring it I have enrolled in Medicare. I wonder, if the machine requires major repair or replacement, will Medicare cover that and what hoops do I have to go through to get a replacement? Sleeping with CPAP until I figure it out!
Thanks for any tips.
RE: Airsense 10 System Fault 010 has me out of commission - Phaleronic - 09-29-2024
Hello G,
Did you take the machine apart again to make sure the flow sensor grommets didn't get pinched/squished when you reassembled the machine? That's usually the issue when seeing that code when replacing a motor on the AS10.
RE: Airsense 10 System Fault 010 has me out of commission - gregger - 09-30-2024
Hi P.,
Yes, good thinking. That actually was my first thought as well.
I took the machine apart, found that the seal of the grommets against the board fittings was perhaps slightly "off," and very carefully resecured them firmly against the flow sensor on the PC board. I also made sure the PC board itself was mounted securely so as not to allow any wiggling that might compromise the grommets' connection. Also made sure the board traces to the sensor looked okay. Then reassembled all. Regrettably, I still got the error message on restart.
RE: Airsense 10 System Fault 010 has me out of commission - SarcasticDave94 - 09-30-2024
If the CPAP is 6 years old, get one of your physicians to order a new replacement via Medicare.
RE: Airsense 10 System Fault 010 has me out of commission - gregger - 09-30-2024
Hi SD,
Thanks, good thought. I have put that into motion and I will see how soon I can get an Rx issued to my supplier, who said it will take at least a week to get it all going. So if there is anything else I can do in the meantime, I'll do it. As we CPAP users know, "Every night counts!"
RE: Airsense 10 System Fault 010 has me out of commission - SarcasticDave94 - 09-30-2024
Hope you get therapy going again ASAP.
RE: Airsense 10 System Fault 010 has me out of commission - Phaleronic - 09-30-2024
Hey gregger, Dave is right you need to get a new machine asap, but I would also suggest keeping this old one even with the fault colde as a backup for you in an emergency.
RE: Airsense 10 System Fault 010 has me out of commission - gregger - 09-30-2024
Agree with you both, thanks.
Unfortunately this machine won't operate at all with that system fault, so I think I'd have to find a used PC board to get it working again. Might be worth a shot.
RE: Airsense 10 System Fault 010 has me out of commission - Nightynite - 09-30-2024
I replaced my blower motor and accidentally put it in backwards in the blue silicone boot.
It blew at a high speed and I immediately knew what I did. I shut it off, flipped the motor and all was fine. I never saw a code. But it was only on for 20 seconds or so.
RE: Airsense 10 System Fault 010 has me out of commission - Phaleronic - 09-30-2024
(09-30-2024, 03:31 PM)gregger Wrote: Agree with you both, thanks.
Unfortunately this machine won't operate at all with that system fault, so I think I'd have to find a used PC board to get it working again. Might be worth a shot.
Yep, I'd go that route, I've seen some of the systemboards on ebay