Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

AirCurve 10 stopped working
#1
AirCurve 10 stopped working
My AirCurve 10 ASV started up last night and quit within a few seconds of operation. Anybody know where the fuse or circuit breaker is or has other advice for me on how to troubleshoot?

 
Post Reply Post Reply
#2
RE: AirCurve 10 stopped working
Try to power-cycle the machine by disconnecting all power and then plugging things back in. If it still does not re-power, the most likely fault is the AC/DC power adapter brick which will be under warranty. As an engineer, you're welcome to use a multimeter to verify power at the DC plug, but you should contact your supplier for service
Sleeprider
Apnea Board Moderator
www.ApneaBoard.com

____________________________________________
Download OSCAR Software
Soft Cervical Collar
Optimizing Therapy
Organize your OSCAR Charts
Attaching Files
Mask Primer
How To Deal With Equipment Supplier


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
RE: AirCurve 10 stopped working
(04-13-2017, 09:05 AM)Papit Wrote: My AirCurve 10 ASV started up last night and quit within a few seconds of operation. Anybody know where the fuse or circuit breaker is or has other advice for me on how to troubleshoot?

Papit, would you define a few seconds please.

Sleeprider's advice is always very good.  To add to it; I would turn off the autostart feature.  This will ensure the machine isn't misinterpreting flow and shutting down the blower.

The humidifier is internal; but can be turned off.  I would turn it off just to reduce power.  If it works with humidifier off, then the power brick may be marginal on power capacity due to a defect.

You might request the clinician's manual for your unit -- see "CPAP Setup Manuals" at top of page.

You will likely have to turn it in for warranty service or replacement.

And, if I may ask, which branch of engineering are you specialized in for your PE?

Kind Regards.

Mongo
Admin Note:
JustMongo passed away in August 2017
Click HERE to read his Memorial Thread

~ Rest in Peace ~
Post Reply Post Reply
#4
RE: AirCurve 10 stopped working
I took a measurement with a voltmeter.   You got it right.  The brick is giving zero output.  Thank you, Sleeprider.
Post Reply Post Reply
#5
RE: AirCurve 10 stopped working
I did the check with my meter.  (I'm an EE per your question.)   You got it right.  The brick is giving zero output.  Thanks, Mongo.  I'm guessing you're where the action is.  Thank you for your service out there.  Be safe.
Post Reply Post Reply
#6
RE: AirCurve 10 stopped working
(04-13-2017, 09:05 AM)Papit Wrote: My AirCurve 10 ASV started up last night and quit within a few seconds of operation. Anybody know where the fuse or circuit breaker is or has other advice for me on how to troubleshoot?

 

afaik there is none

check your circuit breaker did not trip
check voltage at the wall outlet
if you can, check voltage out of the power supply 
if all good then the machine needs professional servicing
Post Reply Post Reply
#7
RE: AirCurve 10 stopped working
(04-13-2017, 11:03 AM)Papit Wrote: I did the check with my meter.  (I'm an EE per your question.)   You got it right.  The brick is giving zero output.  Thanks, Mongo.  I'm guessing you're where the action is.  Thank you for your service out there.  Be safe.

EE here too. Never took the PE exam. Did take the EIT years ago.
On my S9 machine the power connector to the machine is 3 pins.
The 10 series machines are tri-axial. Common, 24 VDC and a third conductor that carries the Thévenin equivalent of 3.3 VDC with a 2.7 k resistor.
Even with a good 24 VDC, if the 3rd conductor Thévenin equivalent is out of spec, the machine won't like it.
Admin Note:
JustMongo passed away in August 2017
Click HERE to read his Memorial Thread

~ Rest in Peace ~
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  airsense 10/11 aircurve 10 heated tube only eok361 0 114 11-19-2024, 11:30 PM
Last Post: eok361
  Help with ASVAuto ResMed AirCurve 10 settings (and esophageal pain) RowG 2 159 11-17-2024, 08:34 AM
Last Post: RowG
  [Equipment] AirCurve 11 vs AirSense 11? UKFan643 3 282 11-12-2024, 11:02 AM
Last Post: sllama
  resmed as10, as11 aircurve 10 daylight savings time end eok361 10 488 11-09-2024, 08:05 PM
Last Post: specialed2000
  [Mod Note] Resmed AirCurve 11 Users Crimson Nape 0 178 11-09-2024, 06:38 PM
Last Post: Crimson Nape
  >> Attention: Resmed AirCurve 11 Users << Crimson Nape 2 262 11-09-2024, 01:25 PM
Last Post: sauerkraut
  Aircurve 10 ASV Periodic Pressure Surges cause leaks scooterbill 2 180 11-04-2024, 04:31 PM
Last Post: SarcasticDave94


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.