11-07-2024, 03:18 AM
(This post was last modified: 11-07-2024, 03:33 AM by walshy1009. Edited 1 time in total.
Edit Reason: Forgot to add something in
)
Pimp My CPAP! (Please rate my data)
Hello CPAPers!
I just recently purchased an ez Share SD card for my CPAP machine (AirSense 11 AutoSet) so as to be able to view more detailed data using OSCAR.
I've been using the AS11 for a while now with my average AHI being 2 - 4 (down from an AHI of 32 in my sleep study), in conjunction with the AirTouch F20. Given that I do toss and turn in my sleep, as well as sleep with my mouth open and on occasion dribble, I am aware the F20 may not be the best choice. However, it is the mask I was most satisfied with using after trialing several different ResMed masks.
Just wondering if I can get some advice based on the below data of what I can do better?
EDIT: Forgot to mention that I do not use the humidifier built into the AS11 as I prefer the dry cold feel (weird I know).
Cheers!
11-07-2024, 06:28 AM
(This post was last modified: 11-07-2024, 06:29 AM by SarcasticDave94.
Edit Reason: Typo
)
RE: Pimp My CPAP! (Please rate my data)
The mask is leaking pretty frequent and too high to ignore.
Your start pressure of 4 is too low. Change it to 6 or 7. Then edit EPR.
EPR 1 is set to Ramp only and will not function until events push your min pressure to 5. Make this full time.
Ramp, starting at 4 as you are Ramp isn't needed. It is robbing you of therapy time. Even when you change min pressure, try to do without Ramp.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEBSITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
RE: Pimp My CPAP! (Please rate my data)
Cheers Dave!
I actually turned off ramp a few nights back but it doesn’t seem to have reflected in OSCAR yet.
Have gone ahead and changed the minimum to 6 and EPR to full time so we’ll see what happens!
Mask leaking is definitely an issue but it is the most comfortable mask for me so am hoping I can change my sleeping habits before resorting to other solutions.
RE: Pimp My CPAP! (Please rate my data)
Ok so my results from last night were worse haha.
HOWEVER, this is probably due to me making the mask fit with the straps quite a bit looser so I'll be tightening them up again tonight and we'll see what happens!
RE: Pimp My CPAP! (Please rate my data)
Ok I think I'm finally getting somewhere. My first night with 0% leak over redline. Any improvements I can make from here?
RE: Pimp My CPAP! (Please rate my data)
Consider EPR full time 2 to address the flow limits. These FL are untimed events that's roughly about a half strength Apnea in restriction. Being untimed, they're not actual Apnea, however can be quite disruptive themselves.
Find out how EPR 2 affects all your event lines and how you feel. After this, you might yet need EPR to go to 3 and min pressure to 7 as one 2 step edit. EPR 3 needs the min 7 to work truly full time, just like EPR 2 needs 6 min pressure.
Keep an eye on CA, but it's OK now.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEBSITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
RE: Pimp My CPAP! (Please rate my data)
Changed my EPR to 2 and got the following results from last night...
