Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.
Login or Create an Account
Machine: Airsence 10 Autoset Mask Type: Full face mask Mask Make & Model: Resmed F20 Humidifier: Climate Line Air CPAP Pressure: 4 to 20 CPAP Software: myAir
New to this great forum - I've been using the Airsense 10 for 6-7 months and some nights I get this massive airflow coming into my F20 full face mask which wakes me up.
It seems the only way to stop the strong airflow is to turn the machine off and then back on (sometimes 2-3 times a night). This doesn't happen every night but maybe 3-4 times a week.
My sleep study had me at AHI 6 (allegedly)
My machine has me at an average AHI of 1.1
The machine is set to Auto 4cm to 20cm and EPR Level 1
Ramp is set to Auto.
I believe a setting or two needs to be adjusted but I have no idea where to start.
Thanks for any and all responses.
For us to help you we need to see Oscar charts. At the top of each page, you'll see a link to Oscar in the black section. Click on that and you'll find instructions on how to use it.
Your machine is at default settings. Although, with an AHI average of 1.1 AHI, you're not doing too bad.
I suspect that what you're feeling may be the result of flow limitation causing your pressure to ramp up high.
Let's try to narrow your pressure range to minimum 7cm, maximum 15cm, with EPR set at 2.
This will give us some idea where to go from there.
We need to see some data...... Download the free OSCAR software. Be sure you have an SD card inserted while you sleep. After a night or two, come back to this thread and post a couple Screenshots from the Daily Page.
Use the links below in my Signature Line to guide you.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Machine: Airsence 10 Autoset Mask Type: Full face mask Mask Make & Model: Resmed F20 Humidifier: Climate Line Air CPAP Pressure: 4 to 20 CPAP Software: myAir
Machine: Remediated Dreamstation APAP-CPAP Mode Mask Type: Full face mask Mask Make & Model: Airfit F20 Humidifier: Built In CPAP Pressure: CPAP 15cmH2O CPAP Software: OSCAR
As Opalrose stated please for now set your machine to these settings:
minimum 7cm, maximum 15cm, with EPR set at 1, ramp OFF
For now this will narrow down the pressure range and help with sleep-once we have Oscar data after this settings change we can see how you're doing with therapy.
Machine: Airsence 10 Autoset Mask Type: Full face mask Mask Make & Model: Resmed F20 Humidifier: Climate Line Air CPAP Pressure: 4 to 20 CPAP Software: myAir
Here is a couple of screenshots from one night's data after changing the settings to 7 and 15 with EPR 2.
Let me know if I should post a few more nights or maybe less detail.
Thanks again for your help.
The problem is evident. You have quite a bit of mask leaking. The algorithm tries to compensate by increasing the air flow during high leaks. Some folk are more sensitive to increases in pressure. We can lower the maximum pressure to 12, but at the same time you'll need to figure out how to control the leaks.
Do you move around at night? Or you are laying in a way that your pillow pushes on your mask?
When you repost a chart, eliminate the calendar so that we can see all the statistics and settings.
Just want to add, that if you feel you are overly sensitive to pressure swings, we can try Cpap mode, with a steady pressure of 7, EPR set at 1. But try to get the leaks under control.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Machine: Airsence 10 Autoset Mask Type: Full face mask Mask Make & Model: Resmed F20 Humidifier: Climate Line Air CPAP Pressure: 4 to 20 CPAP Software: myAir
Thank you and your answer makes perfect sense.
Since I've been doing my cpap machine the mask has been the most frustrating part. I started out with a nose pillow mask and after a week I had a crazy rash around my nose. In thinking I was allergic to silicone I switched to the full face mask with foam thinking this would be better since I'm a mouth breather.
After a while it didn't seem to seal very good after multiple daily adjustments so I decided to try the silicone full face mask which is where I'm at now (guess I'm not allergic to silicone) and obviously I'm still not getting a great seal all of the time.
I will leave my settings at 7 / 15 / 1 for now and focus on getting a good seal.
