Mask: Bleep DreamPort Sleep Solution
Hello Guest,
Welcome to Apnea Board !As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address. Login or Create an Account
Help with new AirCurve 10 VAuto Settings
|
04-24-2024, 01:17 PM
RE: Help with new AirCurve 10 VAuto Settings
Your leaks are not significant enough to worry about. If you look at the panel to the left of your chart you will see that your leaks are listed as 1.45. That's because all but that small amount are not high enough to interfere with your therapy.
Machine: ResMed AirCurve 10 Vauto
Mask: Bleep DreamPort Sleep Solution
04-24-2024, 03:36 PM
RE: Help with new AirCurve 10 VAuto Settings
I originally gave up cpap because I could not handle the "elephant trunk" hose coming off the front of the full face mask and the constant leaks. It was only after I learned of the dreamwear mask that I gave it a try and had good success with cpap, which I now cannot sleep without. As for the kinking, I wasn't talking about the hose kinking but rather the air chambers that run from the top of the dreamwear mask down the sides of my face...I sleep on my side. I'm using the heated hose for the first time and it adds an additional strain on the top of the dreamwear mask that I'm thinking could be binding and resticting airflow in certain situations. Will give the suggestions above a try regarding changes to ramp etc.
Thank you!
04-24-2024, 03:52 PM
RE: Help with new AirCurve 10 VAuto Settings
I used to use the Dreamwear, then the ResMed nasal mask that brought the air in from the top. I never had any problem with not getting plenty of air in both nostrils. I sleep on my back due to back pain, but early on I tried some side sleeping as that was deemed the best by most on the board. I could breathe through both nostrils with no problem when I slept on my side. Those are great masks, and I wouldn't worry about the air getting through.
Machine: ResMed AirCurve 10 Vauto
Mask: Bleep DreamPort Sleep Solution
04-24-2024, 06:34 PM
RE: Help with new AirCurve 10 VAuto Settings
You cann COMPLETELY cut the air onone side and still have enough air coming in the other side with no problem at all!
Apnea (80-100%) 10 seconds, Hypopnea (50-80%) 10 seconds, Flow Limits (0-50%) not timed Cervical Collar - Dealing w DME - Chart Organizing
04-25-2024, 05:22 PM
RE: Help with new AirCurve 10 VAuto Settings
(04-24-2024, 01:17 PM)Deborah K. Wrote: Your leaks are not significant enough to worry about. If you look at the panel to the left of your chart you will see that your leaks are listed as 1.45. That's because all but that small amount are not high enough to interfere with your therapy. But the leak graph shows lots of time where the leak rate is elevated. Yes, it's below the acceptable level so in that regard it doesn't interfere with therapy, but the low level leaks last for a long time and indicate significant mouth leaking. This could be interfering with the quality of sleep. Just my opinion based on my experience with a similar leak pattern.
Sleepster
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
04-25-2024, 05:48 PM
RE: Help with new AirCurve 10 VAuto Settings
(04-24-2024, 03:36 PM)aubreyjs Wrote: I originally gave up cpap because I could not handle the "elephant trunk" hose coming off the front of the full face mask and the constant leaks. I understand. When I started I couldn't tolerate a nasal mask. I would sweat and make it leak, so I switched to nasal pillows and wore those for a few years. I had a similar leak pattern to what you had. Then I tried a full face mask and to my surprise I could tolerate it and I started feeling more rested. My point is simply that as we adapt to CPAP therapy, things we originally found intolerable become tolerable.
Sleepster
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
04-26-2024, 09:10 AM
RE: Help with new AirCurve 10 VAuto Settings
Agreed sleepster, the entire process is to try and obtain a healthy comfortable night of sleep. Plenty of examples of "what's old is new again" with a different mindset.
|
« Next Oldest | Next Newest »
|
Possibly Related Threads... | |||||
Thread | Author | Replies | Views | Last Post | |
[Treatment] BIPAP Settings - ResMed AirCurve 11 Vauto | dcbauman | 20 | 731 |
12-17-2024, 03:42 PM Last Post: Sleeprider |
|
Resmed Aircurve 10 ASV | Rhodesie | 2 | 125 |
12-16-2024, 10:43 PM Last Post: Rhodesie |
|
Air leaks with Aircurve 11 ASV for CA | chrishark | 11 | 431 |
12-15-2024, 08:16 PM Last Post: Jay51 |
|
New to Resmed Aircurve 11 ASV, need help with settings | gcoll | 2 | 171 |
12-14-2024, 10:37 AM Last Post: Sleeprider |
|
Aircurve VAuto PS...pros & cons | WW4B | 10 | 343 |
12-13-2024, 10:09 PM Last Post: SarcasticDave94 |
|
[Equipment] Aircurve 10 buzzing like a fly | Shalom | 3 | 175 |
12-13-2024, 09:46 AM Last Post: Shalom |
|
I need Help with AirCurve 11 settings. | skcampbell2 | 2 | 215 |
12-07-2024, 02:19 PM Last Post: skcampbell2 |