Currently I use the heated ClimateLineAir with my AirSense 10 For Her.
I mentioned to my sleep Tech the continual dry mouth.
She suggested the ClimateLineAir Oxy might be able deliver more humidity because of its larger diameter, so I loaned a (brand new) hose and ran some preliminary tests.
Rating for delivery of more moisture:
(this rating does not apply to those that use the Oxy hose for other reasons).
Ease of use:
ClimateLineAir Oxy plugs in easily and works as stated.
Intro:
Hose, Internal Diameter, Length, Model, Connector
ClimateLineAir, 15 mm, 2 m, 37296, Std mask fitting
ClimateLineAir Oxy, 19 mm, 1.9 m, 37357, Std mask fitting
The standard Resmed blue hose cover fits both hoses.
The hoses have the same grey mask connector so will fit all standard masks.
ClimateLineAir is listed for Resmed 10 series: internal diameter = 15 mm.
ClimateLineAir Oxy is listed for Resmed 10 series and has Internal Diameter of 19 mm: this equates to an increase of cross-sectional area of around +60%.
It fits neatly into the back of the AirSense 10 For Her and the same message comes up: ClimateLineAir connected.
Note: this is designed for use with an Oxygen feed. I made sure the end cap of the Oxygen connector remained shut.
Method:
So I ran a few preliminary tests over a couple of days: back to back tests for one hour using different masks, sitting quietly whilst reading. All settings (pressure, EPR, For Her, manual climate control and hose temperature) were kept the same. Room Temp and Humidity were recorded.
I filled the HumidAir with fresh 100 ml water at the beginning of each hour and then emptied the water and worked out how much water was used for each hour.
Results are in the attachment at the end of this post.
Limitations:
1. These were short 1 hour runs only, and may not reflect the results of a full night.
2. Also note the pressures remained constant during the testing because, of course, I was awake.
I have no idea how this would change for a full night testing with Flow limitations and increased pressures.
3. I did not test for different Hose temperature settings or compare Climate control Manual vs Auto.
4. Water used only equates to Water Delivered to the user with front connecting masks. Top connecting hoses may have some water vented out the top of the headgear connector, and so Water Used will not be the same as Water Delivered.
Results:
Water used:
For some masks there was no difference in the amount of water used.
For one mask there was a slight increase in the amount of water used, but not enough to warrant buying this for that reason alone.
Noise: both hoses were equally quiet, no noticeable difference in noise at the pressures tested. I can’t comment on what the blower might sound like if pushing through higher volumes of air at higher pressure.
Weight: the ClimateLineAir Oxy did feel a bit heavier but I didn’t notice any difference in the amount of pulling on the masks.
Comfort:
The ClimateLineAir Oxy delivered the air in the same way for the F30 M with Quiet Air connector, Amara View with Large cushion, DreamWear MW, P30i Large with holes and P30i Large with mesh.
With the F30 this felt a little more pulsatile but still acceptable.
Most noticeably however with the F30i mask the delivery of air was not so smooth, but much more pulsatile, sort of a high amplitude, low frequency pulsation. I suspect the machine algorithm was trying to compensate for something. (same sensation when temporarily switching to Soft Mode and the AutoSet mode). This felt very uncomfortable to the point of me not wanting to buy this even if the delivery of humidity was significantly better.
The only acceptable result was when using the ClimateLineAir Oxy with the Resmed F30 M mask used with the Standard elbow, with a 25% increase in Humidity Delivered.
This would also be achieved by dialling up the Manual Humidity setting.
Conclusion:
Preliminary results over 1 hour period with stable settings tell me that it is not worth using the ClimateLineAir Oxy if the only purpose is to deliver more humidity and reduce dry mouth.